SEAL™ 36V 105Ah Trolling Motor Battery

SEAL™ contains a factory-integrated aerosol suppression device designed to activate automatically during a severe thermal incident inside the battery enclosure, helping to suppress and contain the event. It adds a layer of protection alongside the battery management system (BMS).

The sealed suppression device requires no routine maintenance and is not user serviceable. Do not open or attempt to recharge it. If activation or damage is suspected, stop using the battery and contact ABYSS for guidance.

Yes. SEAL™ has a pre-installed circuit breaker that helps protect against overcurrent by interrupting the circuit. It works alongside the BMS protections for voltage, current and temperature.

Your installer should confirm the cable sizing, connections and any additional circuit protection required by the complete installation and trolling motor manufacturer. If the breaker trips repeatedly, have the cause diagnosed before returning the system to service.

Yes. The integrated base tray is included and ships with the SEAL™ battery, along with securing straps. You do not need to purchase a separate SEAL™ mounting tray.

Secure the tray to a sturdy mounting surface and use the supplied straps to hold the battery in place. Check the current battery footprint, cable clearances and mounting requirements in the SEAL™ owner's manual before installation.

Yes. SEAL™ is a complete 36V-class, 105Ah lithium trolling motor battery designed to replace a bank of three 12V batteries connected in series for a compatible 36V motor.

Have your installer check the existing charger, wiring and connections for the new configuration. SEAL™ must not be connected in series or parallel with other batteries; use it as the single battery specified in the SEAL™ installation guide.

Start with the exact motor model and its required operating voltage. SEAL™ is intended for compatible 36V trolling motors, including supported models from Minn Kota, Rhodan, Garmin, Power-Pole, Lowrance, MotorGuide and Simrad.

Before ordering, have your dealer or installer confirm the motor's voltage, current demand, connections and installation requirements against the current SEAL™ specifications. Compatibility should be checked by model and configuration, rather than by brand alone.

Use a charger approved for the SEAL™ 36V LiFePO4 battery and configured to its specified lithium charging profile. ABYSS can help match a compatible 36V AC charger and the correct connection cable to your installation.

Have ABYSS or your installer confirm your existing charger's model and settings before reusing it. Do not connect the separate 12V outputs of a three-bank charger to this single 36V battery.

Yes, with compatible charging equipment. A correctly configured SHARK™ DC-DC charger can transfer charging power from the boat's alternator-fed 12V system to the SEAL™ battery. Compatible MANTA™ MPPT equipment provides a solar charging option.

These are system components that must be matched to the boat, battery and connection cables. Confirm the charger, solar equipment and cable requirements for your selected package with your dealer before installation.

SEAL™ communicates with the CRYSTAL™ X3 battery monitor. The X3 displays battery information and provides the Bluetooth connection used with the ABYSS app when your phone is within range.

Use the specified communication cables, and confirm the monitor and cable contents of your selected package when ordering. Ask your dealer to demonstrate charge status, operating information and app connectivity during commissioning.

Runtime depends on average motor current, speed, wind, current, boat load and the reserve you choose to keep. Capacity alone cannot guarantee a full day on the water.

For initial planning, divide 105Ah by the motor's average current draw in amps to estimate hours. For example, a 20A average draw gives a theoretical estimate of 5.25 hours before allowing for reserve and operating conditions. Your dealer can use your motor specifications and fishing style to help size the system.

Confirm 36V motor compatibility and current limits, secure the tray and straps, specify the wiring and circuit protection, configure an approved charger, and verify charging and monitoring operation. Follow the current SEAL™ owner's manual and the motor manufacturer's instructions.

For OEM installations, confirm the required CAN/COM equipment and any display or network integration with ABYSS before specifying the system. Record the serial number, charger configuration, wiring plan and commissioning results, and provide the owner with operating and warranty-registration instructions.

Switch the battery off and follow the owner's manual to isolate connected loads that could drain it during storage. Keep the battery in a suitable dry location protected from damage.

Follow the SEAL™ owner's manual for the storage charge level, temperature limits and checks appropriate to the storage period. Before the next trip, inspect the mounting and connections and verify battery charge and normal operation.

Under the current ABYSS marine lithium warranty policy, qualifying purchases made on or after August 1, 2026 receive 10-year coverage for defects in materials and workmanship, with repair or replacement at ABYSS's discretion. Registration within 90 days, proof of purchase and the battery serial number are required for that coverage. Earlier purchases retain their original warranty terms.

Register through the ABYSS website or app. For technical support, have your serial number, purchase details, motor and charger models, and a description of the issue ready. Review the current warranty policy for the full terms.